ranger tugs

  1. L

    Factory dinghy replacement oars 2022 R-31S

    Could I get information for replacement oars for 2022 R31 factory supplied dinghy? I would like them to attach to the bolts that are on the dinghy already, and all companies I have talked to ask about the brand of the dinghy and that is nowhere to be located. Thank you
  2. N

    R27 Velair AC Not cooling

    Just took delivery on a 2026 R27 with twin 150's. The Velair AC does not cool properly. A few observations. Cabin is 82 degrees, If I set the thermostat to 72 the fans come on and blow air but it is not cool, compressor doesn't kick on and no water pumps. It will only begin pumping and...
  3. H

    Generator Removal

    Is it possible??? I need to do some rather extensive work....lots of rust in the unit and ....its dead as a door nail. I've narrowed the issue down to a 10 amp start control fuse but it is absolutely impossible to access while the unit is on-board. Has anyone else successfully removed theirs...
  4. S

    2022 R27 fresh water system hot water tank replacement

    Hello fellow Tug Nuts, Has any R27 300OB owners replaced their hot water heater? Our 2022 R27 300OB hot water heater is leaking and our freshwater pump will not prime (continues to run) due to not holding pressure. I do not see a bypass valve on my water heater and I am not sure the proper way...
  5. S

    2022 R27 Ranger Tug 300OB water heater

    Ranger Tug, From the 2022 R27 specification sheet, my hot water tank is a 5.3 gallon isotemp and does not have any bypass valve for taking the tank out of the freshwater system. My hot water heater tank has failed (leaking) and my freshwater pump, I think is a (3GPM Shurflo Aqua King model) ...
  6. S

    R23 Dinghy Lift?

    I have a 2017 R23OB. I understand that there is no tilting dinghy rack for this model, but what about it doesn't fit the R23? Is it something I can modify on my end? I have metal fab capabilities, but I'm thinking it might be easier to start with the stock rack (perhaps the one for the R25?)...
  7. S

    2022 R27 Ranger Tug windshield wiper replacement

    Our starboard side windshield wiper arm completely separated from the metal arm. All that is affixed to the windshield is the swing arm and flat metal shaft. It appears I need a 14inch replacement BUT do i need the entire wiper arm OR of can I somehow remount the wiper replacement on the...
  8. C

    Ranger 27 Swim Ladder

    Hello, Is the swim ladder screwed in or bolted to the swim platform? Mine needs to be replaced, it is very rusty, and I am wondering if I need to access the top of the swim platform under the raptor deck to get at nuts for bolts? Thank you Colin Walsh
  9. R

    R27 Thruster

    After using the bow thruster heavily while practicing docking for about an hour, I turned the boat off. When I returned an hour later and turned the boat on and pulled away from the dock the bow thruster made a loud, screeching type of sound and gave no thrust. The boat (R27) is brand new...
    • RickDB
    • Thread
    • 2025 model year bow general questions maintenance r-27 (outboard) ranger tugs
    • Replies: 12
    • Forum: Ask the Ranger Factory
  10. B

    Electric horn replacement parts?

    Ranger tug R-27 (outboard) 2023 model year. The rear cover for one of the Fiamm electric horns has fallen off and gone missing. The horn(s) are A23 Airtone model. Do you know of a source to replace the missing part without having to buy an entirely new set of horns?
  11. R

    Fuel Line for Kicker

    With the factory mounted kicker on an R-23, how do you run the fuel line to the fuel filter for the main tank?
  12. R

    Kicker Fuel Line to Fuel Connection Outlets at the Main Engine on Ranger Tug R-23

    I'm installing a 9.9 kicker on my 2020 Ranger Tug R-23. I noted on another thread the option of tapping into the main fuel tank through the water seperator. But I note that at the engine there is a T-connecror (for lack of a better term it's actually more like an H) with one end capped. Can a...
  13. R

    Installing an outboard motor mount

    I've purchased a Bolton Bear Claw motor mount for my 2020 Ranger Tug R23 and I had a question about installing it. The attached photo shows the cut-out area on the port side of the swim deck and I was wondering whether the bolts for the mount should go through the cover of the cut-out and out...
  14. D

    2023 R25 SeaEra head question

    Hi, Were wondering where the In-line strainer for the SeaEra toilet is located on our 2023 R25 ? We are not getting water flow into the toilet, the seacock is open and the Aqua Jet Wash Down System is operating normally. We are trying to determine what the problem is as the toilet was operating...
  15. G

    Tecma head with false full red light

    2023 32CB with Thetford Tecma head. Red full light permanently lit in spite of tank empty. Emergency flushing works. I did the following, as I am at sea long term for next month: 1. 12v breaker reset, multiple times 2. Check tank with bright light. No obstructions. 3. Cut one wire to high...
  16. N

    2026 R27 with Twin 150s

    I'm in the process of purchasing a 2026 R27 with twin 150s... Will likely close in a couple weeks. After watching Channel surfings recent video from the Seattle boat show covering the same model I'm now seriously considering the wireless hand held helm master ex upgrade. Anyone have any...
  17. B

    R23, how do you replace the windlass solenoid

    Hello, our windlass is no longer going up/down. We do hear it clicking. An electrician indicated that our solenoid needed to be replaced. We've found the solenoid attached to the front panel within the helm panel (assessible from the head). How do you access it to replace it. There isn't...
  18. AKSTEVE70

    ProMariner TruePower Combi 2500Qs

    I have a 2013 R29, with a ProMariner TruePower Combi 2500QS, I am installing new AGM batteries (Starter, Thruster, House). There is a setting for “AGM 1” and “AGM 2” on this charger/inverter. What is the difference and which should I selected for my new AGMs? I am researching Interstate...
  19. AKSTEVE70

    Upgrade to AGM/electrical system

    I am the owner of a 2013 RangerTug (R29). I am replacing the starter, thruster (both Universal UB121100 group 30H) and two (4D) house batteries. I am considering AGM for all. Is there anything I need to know or would need to do to the electrical system if I go this route? Thanks in advance...
  20. G

    Ignition Light Stays Faintly on After DC-DC Charger Installation

    Hello! I recently converted to a lithium set up and when I start my engine (180 hp IB Yanmar), the ignition light remains on faintly. I installed a 50 amp dc-dc charger and have been told that perhaps I need to install a second or possibly even a third dc-dc charger to correct the problem...

  • Tugnuts.com is the community hub for Ranger Tug, Cutwater, and Solara owners. Since its inception in 2008, the Tugnuts forum has grown into an active and thriving community of more than 9,000 members. It serves as both a meeting place for the best boating community online, and an invaluable archive of information.

  • User menu
Back
Top